The Weigao products instructions
A. Use and installation
1, the series (hereinafter referred to as the product) suitable for continuous operation, operation allows both positive and negative directions.
2, the output shaft and the input shaft shaft and other parts fit, does not allow direct thump to prevent damage to the shaft end should be pressed into the screw holes with screws.
3, the output shaft and the input shaft on the shaft extension key using ordinary flat key, in line with the provisions of GB1095-79 "flat key and keyway tolerances.
4, may appear overload occasion, the overload protection device should be installed to prevent the prime mover of the reducer its configuration result in mechanical damage due to excessive torque passing.
5, shall not exceed the permissible rated power or torque of the cases.
6, reducer couplings (Variator) mechanical connection with the work to be the axis concentric reducer installation error couplings used should not be greater than the allowable error value.
7, reducer installed outside (ie, foot type) based on (or infinitely variable speed drive), product calibration, should be replaced into the flat pad configuration of the pad should avoid causing mechanical deformation.
8, after the product is installed, the application of hand rotation is flexible.
9, after the product is installed, before you use must be commissioning gradually loading operation in the case of normal operation.
10 larger impact load, starter frequent base foundation shall, with the positioning pin, or use a hydraulic coupling.
11, in the general case, the horizontal (ie, foot type) products output axis in a horizontal position, the elevation angle of the shaft axis must be tilted no more than 15 ° (the extended end of the output shaft down) vertical (ie flanged ) product output shaft end vertically downward use.
12, before the test machine must look at the oil on whether to adopt the provisions of lubricant (grease), the oil level is up to the required position.
13, the Variator work ambient temperature must not exceed 40 ℃, oil pool temperature rise of no more than 45 ° C, the highest oil temperature generally does not exceed 75 ° C.
14, Variator products factory, the governor limit screw has been adjusted in the limit position. No one shall be arbitrarily adjusted so as not to damage the parts.
15, Variator must speed control in the case of the boot, non-stop governor.
16, the user should pay special attention to product labels for the operation and lubrication requirements
II. Lubricating
1 Weigao products mainly oil bath lubrication, a variety of products used lubricant oil are shown in Table 1.
2, plus oil change system:
IV. Replaced with new oil after the first refueling operation 500 hours of work. Rinse and internal oily; second in 1000-1200 after working hours, replace the lubricant (grease); after every 2000 hours of work to replace the lubricant (grease) once each replacement oil, should be the body's internal rinse. Working conditions (high ambient temperature, humidity, dust, etc.) should be appropriate to shorten the oil change time. Running various reducer (or infinitely variable speed drive) mechanical oil reserves must maintain the required height of the oil level, should not be too much or too little,
Open the vent cap on the base or flange to refueling, in the case of high or low temperature lubricant should reconsider.
Table lubricant oil choice
Product Name
Lubricant (grease)
Remark
□ stepless
Monsanto Mnsauto production Santotrao40 # or 50 # traction fluid
The factory with a special lubricant. I can plant users need long
Period of supply.
□ stepless
□ reducer combination
The part plus stepless CVT machine for oil; reducer part plus the corresponding specified lubricant
The factory is refueling Please observe the label on the product.
□ cycloid
□ FB bellows
□ cycloidal reducer
Recommended by 90 # industrial gear
Oil or deceleration machine grease
The factory of the product plus special oils. The user needs our factory at any time can
Available.
□ variety of cylindrical gear reducer
70 # -120 # medium extreme pressure industrial gear oils
Products factory without refueling, lubricants user-owned lubricant selection, except in exceptional circumstances, to consider the size of the load nature and sliding speed, high load large selection of viscosity the sliding speed large selection of low viscosity.
□ worm reducer
Worm for oil
N680 N460
N320
N220
Note: filling ■ the lubricant (grease) products. |
